|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
excellent quality, contains circuits and scan quality, 110 pages
;
It was easy done, and I got exactly what I was looking for.
;
The manuel was exactly what I needed and I received it promptly. Thanks
;
Thanks to Owner-Manuals.com! This manual was exactly what I needed. As Amana was purchased by Maytag and later by Whirlpool, there was no way to receive it from their websites. I was lucky to find this resource.
 ;
Great to be able to set channels again, on an old but stoll fine working TV
REVERSING THE DOOR OPENING
Your dryer is fitted with a reversible door. To change the direction of opening proceed as follows for your type of door.
Dryers fitted with hinge cover :B
J
J
Fit screw (E) to secure hinge cover. Remove screw (H) at top of door and refit switch strike (B) as shown. Refit buffer (J).
Open the door. Undo screw (A) remove switch strike (B) and replace screw. Undo screw (J) and remove buffer. Remove screws (C) and latch plate (D). Remove hinge cover screw (E). Close the door.
B A
Pull the hinge cover (F) forwards to remove it. Remove two outer screws (G). Remove door. Fit latch plate (D) with screws (C)
Reverse door and fit to dryer in closed position. Refit screws (G) and hinge cover (F). Open the door.
Dryers fitted without hinge cover :2 3
H
B
1
J E C D F G D C E J
Open the door. Undo screw (A) remove switch strike (B) and replace screw. Undo screw (J) and remove buffer. Remove screws (C) and latch plate (D). Remove hinge block screw (E). Remove door from hinge blocks.
Remove hinge screws (F) and hinge (G) and refit to opposite side as shown.
Refit latch plate (D) with screws (C). Remove screw (H) at top of door and re fit switch strike (B) as shown. Refit buffer (J). Fit door to hinge blocks and secure with screws (E)
Large Door Opening :First remove the child safety peg from the top of the door by rotating 90� anticlockwise. Now unscrew the door hinges from the machine by removing the 4 screws. Do not use a power screwdriver as this may damage the screw threads. Remove the four screws from the opposite side of the door opening. Place these screws in the hinge holes on the other side of the door opening. Reverse the door and re apply the hinge screws. Replace the child safe peg in the top of the, now reversed, door.
4213 094 45689
� � � � �
RE-INSTALLING THE CONDENSER
REMOVING THE CONDENSER
NOTE: The condenser will discolour through use.
The condenser and ducting should be cleaned 3 or 4 times a year or more frequently if the dryer is in constant use. See �CLEANING THE CONDENSER� opposite.
may leak if the condenser is not correctly re-installed. Carefully push the condenser back into the machine, until it is pushed fully home and a �click� is heard. Ensure all lint and fluff is removed from around the grille seal before closing or water may leak. IMPORTANT: The dryer Slide the condenser grille catch to the left. Firmly pull the condenser out.
THE CONDENSER
� � � �
CAUTION: For maximum efficiency, the plates are made from very thin aluminium and are easily damaged. Do not try to poke anything between the plates or use a hard object or tool for cleaning. At all times, handle the condenser carefully and avoid crushing the plates.
CLEANING THE CONDENSER
the condenser duct). After cleaning, re-install the condenser (see opposite). Whilst the condenser is removed, clean as much fluff as possible from inside the ducting by reaching a hand into the machine. In particular, keep the passage from the fan clear (on the right hand side of Flush the fluff from between the plates under running water and carefully shake off excess water. Remove the condenser (see opposite).
|
|
|
> |
|
